Search results for "Grain boundary"
showing 10 items of 143 documents
Temperature Coefficients of Crystal Defects in Multicrystalline Silicon Wafers
2020
This article investigates the influence of crystallographic defects on the temperature sensitivity of multicrystalline silicon wafers. The thermal characteristics of the implied open-circuit voltage is assessed since it determines most of the total temperature sensitivity of the material. Spatially resolved temperature-dependent analysis is performed on wafers from various brick positions; intragrain regions, grain boundaries, and dislocation clusters are examined. The crystal regions are studied before and after subjecting the wafers to phosphorus gettering, aiming to alter the metallic impurity concentration in various regions across the wafers. Most intragrain regions and grain boundarie…
How Gettering Affects the Temperature Sensitivity of the Implied Open Circuit Voltage of Multicrystalline Silicon Wafers
2019
The temperature sensitivity of the open circuit voltage of a solar cell is mainly driven by changes in the intrinsic carrier concentration, but also by the temperature dependence of the limiting recombination mechanisms in the cell. This paper investigates the influence of recombination through metallic impurities on the temperature sensitivity of multicrystalline silicon wafers. Spatially resolved temperature dependent analysis is performed to evaluate the temperature sensitivity of wafers from different brick positions before and after being subjected to phosphorus diffusion gettering. Local spatial analysis is performed on intra-grain areas, dislocation clusters and grain boundaries. Lar…
Variable-charge method applied to study coupled grain boundary migration in the presence of oxygen
2009
International audience; One of the important differences between simulation and experiments in grain boundary (GB)-dominated metallic structures is the lack of impurities such as oxygen in computational samples. A modified variable-charge method [Elsener A, Politano O, Derlet PM, Van Swygenhoven H. Modell Simul Mater Sci Eng 2008;16:025006] based on the Streitz and Mintmire approach [Streitz FH, Mintmire JW. Phys Rev B 1994;50:11996] is used to study coupled GB motion in an Al bicrystal with a [1 1 2] symmetrical tilt GB in the presence of substitutional O, and compared with the stick–slip process identified by Cahn and Mishin [Cahn JW, Mishin Y, Suzuki A. Acta Mater 2006;54:4953]. It is found…
Ion track template technology for fabrication of CdTe and CdO nanocrystals
2020
Abstract CdTe and CdO nanocrystals were synthesized by chemical deposition into a-SiO2/n-Si ion track template formed by 200 MeV Xe ion irradiation with the fluence of 108 ions/cm2. Depending on the temperature of the solution CdTe + CdO and single-phase CdO with a hexagonal crystal structure were obtained, respectively. The study of the current – voltage characteristics of the obtained structure with the single-phase CdO allows us to estimate the number of grain boundaries and the height of the potential barrier, as well as the n-type conductivity.
A comparative study on the compatibility of liquid lead–gold eutectic and liquid lead–bismuth eutectic with T91 and SS 316LN steels
2012
Abstract Liquid lead–gold eutectic (LGE) is considered as a potential target material for high power spallation sources. In the present work, the corrosion effects of LGE on T91 and SS 316LN steels have been investigated in comparison with that of liquid lead–bismuth eutectic (LBE) under the same testing conditions. Two tests were conducted at 400 °C for 1800 h and at 450 °C for 1300 h, in which specimens of the two steels were exposed to 1 m/s flowing LGE and LBE. Surface inspections showed that the specimens underwent a mixed corrosion mode of dissolution and oxidation. The results obtained from the SS 316LN specimens are very interesting. Firstly, EDX (electron energy dispersion X-ray sp…
The Grain Boundary Wetting Phenomena in the Ti-Containing High-Entropy Alloys: A Review
2021
In this review, the phenomenon of grain boundary (GB) wetting by melt is analyzed for multicomponent alloys without principal components (also called high-entropy alloys or HEAs) containing titanium. GB wetting can be complete or partial. In the former case, the liquid phase forms the continuous layers between solid grains and completely separates them. In the latter case of partial GB wetting, the melt forms the chain of droplets in GBs, with certain non-zero contact angles. The GB wetting phenomenon can be observed in HEAs produced by all solidification-based technologies. GB leads to the appearance of novel GB tie lines Twmin and Twmax in the multicomponent HEA phase diagrams. The so-cal…
Transport properties of Bi2Sr2Ca2Cu3O10+δ Bicrystal Grain Boundary Josephson Junctions and SQUIDs
1996
Josephson junctions and SQUIDs on 36.8° SrTiO 3 bicrystal substrates were prepared from epitaxial Bi 2 Sr 2 Ca 2 Cu 3 O 10+δ thin films with critical temperatures around 95K. The current-voltage characteristics are well described by the resistively and capacitively shunted junction model. I c R n products of 50μV at 77K and 0.7mV at 4.2K have been reached. The I c (B) dependence is symmetric to B = 0 with an I c suppression of 90% in the first minimum. Nevertheless it turns out, that the junctions are inhomogeneous on a μm scale. SQUID modulations observed at 78K indicate a flux-voltage transfer function of 2.7μV/Φ 0 at this temperature.
ZnMgO-based UV photodiodes: a comparison of films grown by spray pyrolysis and MBE
2016
Detecting the UV part of the spectrum is fundamental for a wide range of applications where ZnMgO has the potential to play a central role. The shortest achievable wavelength is a function of the Mg content in the films, which in turn is dependent on the growth technique. Moreover, increasing Mg contents lead to an electrical compensation of the films, which directly affects the responsivity of the photodetectors. In addition, the metal-semiconductor interface and the presence of grain boundaries have a direct impact on the responsivity through different gain mechanisms. In this work, we review the development of ZnMgO UV Schottky photodiodes using molecular beam epitaxy and spray pyrolysis…
Is there a global carbonate layer in the oceanic mantle?
2021
co-auteur étranger; International audience; Previous modeling of carbonate subduction by high‐pressure experimentation has allowed to propose scenarios for bulk carbon return to the mantle, but the detailed transfer mechanisms have seldom been studied. We monitored carbonate – silicate reactions by combining high‐pressure experiments and synchrotron‐based x‐ray diffraction. Carbonates break down at moderate pressure and high temperature and CO2 is trapped at grain boundaries. Further isothermal compression yields melting, which may control continuous carbon introduction, first in the mantle wedge, and next, away from the wedge. Carbon presence has been discussed in a variety of magmatic con…
Natural gas hydrate investigations by synchrotron radiation X-ray cryo-tomographic microscopy (SRXCTM)
2008
[1] We report the 3D microstructure analyses of natural gas hydrates sampled from Gulf of Mexico. The samples were characterized by synchrotron radiation X-ray cryo-tomographic microscopy (SRXCTM) using the ‘TOMCAT’ beam line at the Swiss Light Source (SLS). The SRXCTM demonstrates its applicability to unlock some microscopic features of the marine hydrates, in particular of crystallite size and grain boundary network. The gas hydrate domains are surrounded by a network of pores of typically a few micrometers, which are largely due to decomposition. Out of the SRXCTM data, the porosity, total volume of the voids, the void surface area and number of the total gas-filled voids have been calcu…